The refrigerator is one of the most important appliances in the house. It can survive without AC or hot water if needed. You can do without hot dishes. However, food preservation is a necessity of modern life. This is a surprising reason when the refrigerator door does not close at all. Maybe the bomb has stopped or you recently had trouble catching the bomb. Click here for more information Subzero Refrigerator Repair in Newport Beach
Even if there is a problem with your refrigerator door, we can help you find the cause and find a solution. Let’s look at 10 ways to fix your fridge door that may or may not close, or close.
1) Clean the seal
The most common problem with refrigeration doors is related to the seal. This is the rubber seal on the outside of the fridge and freezer door. If the gasket is dirty, warped, loose or hardened over time, you won’t be able to create a tight seal that closes the refrigerator with all the cold inside. The easiest solution is to clean the sails, which may have formed a layer of dirt and sand over time. Using a damp sponge or towel, wipe down the entire length of the rubber gasket securely on each available side. A little white vinegar or a bit of dish detergent can help break down oil and residue. A thin coat of petroleum jelly can repair some imperfections and work well on old joints.
2) Replace the seal
Old gaskets that have seen several refrigerators open can be returned or moved. This is a clear recipe for refrigerators that do not complete sealing. If the gasket won’t connect or has become deformed, you can fix it without buying a new gasket by reattaching the old gasket. The accuracy depends on the refrigeration model. Some gaskets are bonded with an adhesive gasket, others use a cement gasket, another type of refrigerator door gasket adhesive.
3) Replace gasket
If the gasket is old or defective, it must be replaced to properly seal the refrigerator. Before you begin, use your refrigerator and model to choose the right gasket replacement.
Carefully remove the old gasket according to the refrigerator manual. Then follow the installation instructions to clean the gasket grooves before using the new gasket. Inspect the seal to make sure the job is complete.
4) Measure your feet
Sometimes the coolant stops sealing due to the door hanging unevenly, which prevents the joints from sealing. This can often happen because the bottom of the refrigerator or the floor is not the same. You may need to adjust the feet if the floor is uneven or if the refrigerator is on a different material, such as carpet. Use a foam or laser level to make sure the bottom of the refrigerator is level. If the floor is level, make sure the legs are all the same height and support the refrigerator horizontally.
5) Tighten the hinges
If your door holds a lot of open, closed, and heavy liters of milk, your fridge door may start to sag through its hinges. Fortunately, this problem is easy to fix. If the hinge works well, you usually only need to attach the hinge from the top, as the pressure exerted on the door will drive the hinge up. However, you may need to tighten the bottom hinges to achieve balance. You may need to remove the plastic cover from the top of the refrigerator door hinges before entering the machine, tighten the connections according to the refrigerator manual, and repair the refrigerator door.
6) Remove items from the door
Another problem is that many items are too heavy on the refrigerator door. If the hinges are tight enough to fit in the safe and the door won’t close, a gallon of milk and other heavy items stored on the refrigerator door will cause the door to crack.
7) Replace damaged hinges
The hinges will be damaged and the doors will be loosened and closed. If you use a heavy door for too long, the hinge will turn, and if you bump into the refrigerator, it may warp. If your hinges are bent, damaged, or rusted, the good news is that you don’t need to replace the entire refrigerator. New hinges can be installed where the old hinges were installed and hold the refrigerator door in place with new strength and reliability.
8) Reorganization of the shelves
Sometimes the problem is as simple as blocking a door. But often times you can begin to see these clogs as problems that need to be fixed. If you use the refrigerator cold enough, the door may clog and close. This problem can often be solved by repairing the refrigerator cabinets. Think about the space you will need and the length of the bowl door that will stick out. By simply moving the space between each shelf and the drawer, you can maximize the efficiency of the refrigerator storage design.
9) Remagnetize the door
If your refrigerator door depends on magnetic force to keep it closed, it seems that the original magnetization will be lost or lost over time. For magnetic refrigerators, you can hire a door repair service.
10) Replace the door
Ultimately, the entire refrigerator door may be the problem. If the door is broken or bent under any circumstances, it will not fully close or re-seal. If you have a problem with your fridge door, you might want to compare the cost and benefits of replacing the entire door or buying a new fridge with every alarm, whistle and warranty.